Class: SSS 3
Term: First Term
Subject: Basic Electronics
Time: 2 Hours 30 Minutes
Total Marks: 70
SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.
- An oscillator uses two capacitors as a capacitive feedback divider across an inductor. Which oscillator topology is indicated? (a) Colpitts oscillator (b) Hartley oscillator (c) Emitter follower alone (d) Full-wave bridge rectifier
- All the following are practical considerations for a satellite receiving system EXCEPT ________. (a) condition of the feed and LNB (b) cable integrity and receiver configuration (c) assuming line-of-sight and antenna alignment can never affect reception (d) proper dish orientation
- Why is controlled negative feedback often useful in an amplifier? (a) It necessarily makes every stage oscillate (b) It can improve linearity, stability or bandwidth within design limits (c) It guarantees zero power consumption (d) It removes the need to measure distortion
- Which distinction between a microphone and loudspeaker is correct? (a) Both are exclusively used to tune an RF oscillator (b) A microphone is always the power supply for the speaker (c) A loudspeaker extracts satellite radio signals from space (d) A microphone converts sound into a signal; a loudspeaker converts a signal into sound
- The low-noise unit positioned near a satellite dish focus and used for initial reception amplification and conversion is the ________. (a) LNB (b) speaker cone (c) telephone microphone (d) battery isolator
- Which of these is not a necessary element of a functioning two-way telephone conversation? (a) A receiving audio output for the other party (b) Communication through an appropriate network (c) Continuous face-to-face contact between the two callers (d) A means of capturing the speaker’s sound
- An amplifier gives \(2.4\,\mathrm V\) output for \(80\,\mathrm{mV}\) input. The voltage gain is ________. (a) \(300\) (b) \(3\) (c) \(0.033\) (d) \(30\)
- Which pairing of an electronic circuit and its chief purpose is correct? (a) Oscillator — producing a periodic signal (b) LNB — final demodulation and direct loudspeaker power delivery (c) Feedback network — preventing any signal from returning to input (d) Amplifier — permanently storing digital photos without power
- A feedback oscillator using a capacitive divider is generally identified as a ________ oscillator. (a) servo (b) Colpitts (c) Wankel (d) Hartley
- All the following can be effects of poorly controlled positive feedback EXCEPT ________. (a) possible instability (b) increased sensitivity to phase shift (c) regenerative signal build-up (d) guaranteed suppression of oscillation at any loop gain
- A phone’s speaker works during media playback but no sound is heard during calls. Which troubleshooting approach is most defensible? (a) Check call audio routing, network path and relevant voice circuitry rather than assuming the speaker is defective (b) Replace the satellite dish without checking the handset (c) Change microphone gain without checking the call signal path (d) Bypass all signal processing circuits
- A satellite receiver reports weak signal on many channels after the dish has shifted during a storm. What should be checked first? (a) The colour of the remote-control buttons (b) Dish alignment and the signal path to the LNB (c) The amplifier output stage of an unrelated radio (d) The television speaker volume as the sole cause
- The main reason for correctly biasing a small-signal amplifier is ________. (a) To remove the need for a power supply (b) To replace all load resistances with magnetic coupling (c) To ensure its output frequency is always zero (d) To establish a suitable operating point and allow faithful signal amplification
- All these are familiar amplifier device implementations EXCEPT ________. (a) a field-effect transistor stage (b) a MOSFET amplifier stage (c) a non-electronic mechanical tyre jack used as the active gain element (d) a bipolar-junction transistor stage
- Which comparison of positive and negative feedback is accurate? (a) Positive feedback reinforces part of the input; negative feedback opposes it (b) Negative feedback is defined as feedback with no phase relation (c) Both always increase stability by the same mechanism (d) Positive feedback can never lead to sustained oscillation
- ________ is the ratio of an amplifier’s output signal amplitude to its input signal amplitude under specified conditions. (a) Wavelength (b) Gain (c) Frequency drift (d) Capacitance
- A designed oscillator fails to start. Which diagnostic sequence is most relevant? (a) Adjust the remote-control battery before examining the board (b) Replace the loudspeaker’s grille as the only intervention (c) Increase output loading without checking gain (d) Check supply and bias, feedback path, resonant network and loop conditions
- An amplifier stage designed for signals in the radio broadcasting frequency range is a(n) ________. (a) digital-to-analogue converter only (b) electromechanical servo (c) radio-frequency amplifier (d) audio power rectifier
- Which combination is necessary for sustained sinusoidal oscillation in a feedback oscillator? (a) Zero energy input and zero amplification (b) A diode rectifier acting without a resonant or timing condition (c) A completely open feedback path (d) A suitable loop phase and loop gain approximately unity at the oscillation frequency
- Which of the following modifications is most likely to reduce amplifier distortion at the expense of some open-loop gain? (a) Applying appropriate negative feedback (b) Shorting the output terminals during operation (c) Disconnecting the bias supply completely (d) Applying uncontrolled positive feedback
- Why should the resonant components of a tuned oscillator be chosen carefully? (a) They determine the price of the satellite television subscription (b) They remove the need for correct circuit connections (c) Their values influence the oscillation frequency and stability (d) They automatically replace the power supply
- Which of these is not a normal reason to use an intermediate-frequency stage in a superheterodyne receiver? (a) To process signals after frequency conversion (b) To eliminate the need to tune any received channel or oscillator (c) To provide gain at a relatively fixed frequency (d) To support selective filtering
- ________ is the portion of a satellite communication link that carries signals from an earth station towards the satellite. (a) Uplink (b) Downlink (c) Audio mixing (d) Local grounding
- ________ is the circuit arrangement in which a signal is returned from output to input in the reinforcing phase under suitable gain conditions. (a) Winding insulation (b) Positive feedback (c) Negative feedback (d) Earth leakage
- Which statement about a basic amplifier is NOT correct? (a) An amplifier can increase a small signal using supply energy (b) Poor biasing can cause distortion (c) Frequency response affects the signals it handles (d) A passive stage without an energy supply can produce arbitrarily large power gain
- A receiving system that converts modulated electromagnetic signals into intelligible information performs signal ________. (a) chassis alignment (b) fuel injection (c) demodulation (d) tread balancing
- Why does the receiver chain use low-noise amplification near the satellite dish feed? (a) The LNB provides the receiver’s final audio power output (b) The television loudspeaker must be placed at the dish (c) Satellites transmit only sound waves through air (d) The incoming signals are weak and should be amplified before further cable loss dominates
- An audio amplifier produces distortion when driven by a much larger signal than its designed range. What is the strongest explanation? (a) The signal exceeds linear operating limits and causes clipping or other nonlinearity (b) Negative feedback always prevents all clipping (c) Every amplifier is distortion-free at maximum input (d) The microphone has become an oscillator automatically
- A telephone sends a speaker’s voice through a network. Which sequence best describes the essential signal process? (a) Send air vibrations through the handset battery directly to the distant ear (b) Transmit only an unmodulated carrier independent of speech (c) Transduce speech to an electrical or digital signal, transmit it, then reconstruct sound at reception (d) Require a physical acoustic tube between subscribers
- Which statement about an oscillator is NOT accurate? (a) It can generate a periodic output using circuit energy (b) An oscillator must always receive a periodic external signal to maintain its output (c) Its frequency can be determined by a resonant or timing network (d) Feedback may sustain oscillations under suitable conditions
- Which of these is not a legitimate application of oscillators? (a) The claim that a clock signal creates electrical energy without any source (b) Generating timing signals for computers (c) Providing carriers for communication (d) Timing circuits in alarm devices
- Why should an RF amplifier’s frequency response be considered separately from an audio amplifier’s? (a) An RF amplifier must reproduce low-frequency sound acoustically (b) Signal frequency has no bearing on circuit design (c) They process signals in different frequency ranges and require different matching/selectivity (d) Both operate only at zero frequency
- An amplifier with feedback has reduced midband gain but improved consistency across devices. Which mechanism best explains this? (a) Positive feedback has automatically increased distortion (b) The transistors no longer require biasing (c) The output has become a DC supply rather than a signal (d) Negative feedback makes overall gain less dependent on variations in open-loop gain
- Which distinction between the satellite dish and receiver decoder is correct? (a) The receiver decoder replaces the need for any antenna (b) The dish gathers radio-frequency energy; the decoder processes received information into usable output (c) Both perform only mechanical sound amplification (d) The dish decrypts all channels while the decoder reflects radio waves
- A satellite receiver does NOT primarily use its LNB to ________. (a) convert an incoming broadcast into a printed newspaper (b) convert a received band into a lower intermediate band (c) amplify weak high-frequency signals (d) improve the usability of signals collected by the dish
- An amplifier intended to amplify signals from a microphone for a loudspeaker is primarily an ________ amplifier. (a) satellite downlink-only (b) audio-frequency (c) oscillator-only (d) microwave filter
- Which order best represents the receiving path for satellite television? (a) Decoder → loudspeaker → dish → LNB (b) Audio section → satellite uplink → dish → LNB (c) Dish/antenna → LNB → receiver/decoder → audio-visual output (d) LNB → household socket → dish → transmitter
- The oscillator circuit that uses a tapped inductor or inductive divider in its feedback network is the ________ oscillator. (a) astable multivibrator only (b) relaxation RC-only (c) Colpitts (d) Hartley
- The correct step in investigating an amplifier that clips near its supply rails is to ________. (a) Retune the RF front end without checking the amplifier bias (b) Examine input amplitude, bias point and supply headroom (c) Assume clipping proves the loudspeaker is disconnected (d) Replace the radio aerial immediately
- A feedback amplifier becomes unstable and produces a tone when gain is increased. What should the designer investigate? (a) A change in component marking that leaves feedback phase unaffected (b) A rise in load impedance that cannot change the loop gain (c) Loop gain and phase conditions that may turn intended feedback into regenerative feedback (d) The packaging colour of the active device
SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.
1. Answer the following questions.
(a) A signal amplifier gives 3.6 V output for a 120 mV input. Calculate its voltage gain and show how the input units are reconciled. (5 marks)
(b) Analyse five ways biasing, gain, distortion or feedback can affect the quality of an amplifier output. (5 marks)
2. Answer the following questions.
(a) Compare Hartley and Colpitts oscillators using five circuit or operating features. (5 marks)
(b) Explain five factors needed to obtain and maintain useful oscillation in a feedback oscillator. (5 marks)
3. Answer the following questions.
(a) Trace the satellite receiving signal from dish to programme output in five meaningful stages. (5 marks)
(b) Explain five reasons poor dish alignment, cable or LNB condition can impair reception. (5 marks)
4. Answer the following questions.
(a) Explain five distinct processes involved in transmission and reception of a telephone voice signal. (5 marks)
(b) A working radio receiver has unstable gain. Describe five checks or adjustments involving its amplifier and feedback stages. (5 marks)
OBJECTIVE MARKING SCHEME
Question 1 – ✅ (a) Colpitts oscillator
Question 2 – ✅ (c) assuming line-of-sight and antenna alignment can never affect reception
Question 3 – ✅ (b) It can improve linearity, stability or bandwidth within design limits
Question 4 – ✅ (d) A microphone converts sound into a signal; a loudspeaker converts a signal into sound
Question 5 – ✅ (a) LNB
Question 6 – ✅ (c) Continuous face-to-face contact between the two callers
Question 7 – ✅ (d) \(30\)
Question 8 – ✅ (a) Oscillator — producing a periodic signal
Question 9 – ✅ (b) Colpitts
Question 10 – ✅ (d) guaranteed suppression of oscillation at any loop gain
Question 11 – ✅ (a) Check call audio routing, network path and relevant voice circuitry rather than assuming the speaker is defective
Question 12 – ✅ (b) Dish alignment and the signal path to the LNB
Question 13 – ✅ (d) To establish a suitable operating point and allow faithful signal amplification
Question 14 – ✅ (c) a non-electronic mechanical tyre jack used as the active gain element
Question 15 – ✅ (a) Positive feedback reinforces part of the input; negative feedback opposes it
Question 16 – ✅ (b) Gain
Question 17 – ✅ (d) Check supply and bias, feedback path, resonant network and loop conditions
Question 18 – ✅ (c) radio-frequency amplifier
Question 19 – ✅ (d) A suitable loop phase and loop gain approximately unity at the oscillation frequency
Question 20 – ✅ (a) Applying appropriate negative feedback
Question 21 – ✅ (c) Their values influence the oscillation frequency and stability
Question 22 – ✅ (b) To eliminate the need to tune any received channel or oscillator
Question 23 – ✅ (a) Uplink
Question 24 – ✅ (b) Positive feedback
Question 25 – ✅ (d) A passive stage without an energy supply can produce arbitrarily large power gain
Question 26 – ✅ (c) demodulation
Question 27 – ✅ (d) The incoming signals are weak and should be amplified before further cable loss dominates
Question 28 – ✅ (a) The signal exceeds linear operating limits and causes clipping or other nonlinearity
Question 29 – ✅ (c) Transduce speech to an electrical or digital signal, transmit it, then reconstruct sound at reception
Question 30 – ✅ (b) An oscillator must always receive a periodic external signal to maintain its output
Question 31 – ✅ (a) The claim that a clock signal creates electrical energy without any source
Question 32 – ✅ (c) They process signals in different frequency ranges and require different matching/selectivity
Question 33 – ✅ (d) Negative feedback makes overall gain less dependent on variations in open-loop gain
Question 34 – ✅ (b) The dish gathers radio-frequency energy; the decoder processes received information into usable output
Question 35 – ✅ (a) convert an incoming broadcast into a printed newspaper
Question 36 – ✅ (b) audio-frequency
Question 37 – ✅ (c) Dish/antenna → LNB → receiver/decoder → audio-visual output
Question 38 – ✅ (d) Hartley
Question 39 – ✅ (b) Examine input amplitude, bias point and supply headroom
Question 40 – ✅ (c) Loop gain and phase conditions that may turn intended feedback into regenerative feedback
THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: 120 mV = 0.12 V (2), Av=3.6/0.12 (1), gain 30 (2).
(b) 5 marks: Bias point, clipping, frequency response, negative feedback, noise and load effects; any five accurate explained 1 each.
Question 2 (10 Marks)
(a) 5 marks: Inductive divider vs capacitive divider, LC resonance, feedback mechanisms, frequency-setting elements and applications; five 1 each.
(b) 5 marks: Correct bias/power, adequate loop gain, feedback phase, frequency-selective network, load/stability; five 1 each.
Question 3 (10 Marks)
(a) 5 marks: Dish collection, LNB low-noise amplification, frequency conversion, decoder/demodulation, audio/video output; five 1 each.
(b) 5 marks: Antenna gain, signal path loss, feed alignment, noise contribution, frequency conversion and weather/exposure; five 1 each.
Question 4 (10 Marks)
(a) 5 marks: Sound capture, transduction/encoding, transmission, network routing, decoding/reconstruction; five 1 each.
(b) 5 marks: Supply stability, component/bias health, signal input level, feedback network, frequency response, grounding/shielding; five 1 each.

Community Join the conversation Open discussion +