Class: SSS 3
Term: First Term
Subject: Auto Mechanic Work
Time: 2 Hours 30 Minutes
Total Marks: 70
SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.
- Which description of positive camber is correct? (a) The front edges of both tyres point closer together (b) The wheel rotates faster than the axle (c) The top of the wheel leans outward relative to its lower edge (d) The steering axis is vertical by definition
- All these may be considered during a decarbonisation assessment EXCEPT ________. (a) assuming every carbon deposit can be removed by increasing tyre pressure (b) appropriate workshop cleaning and safety procedures (c) engine condition and operating symptoms (d) evidence of deposit accumulation
- The main reason for the inner wheel turning through a greater angle in a low-speed corner is to ________. (a) increase the engine firing order (b) avoid any need for suspension travel (c) keep both wheels on exactly the same circular path (d) reduce tyre scrubbing as the wheels follow different turning radii
- What is a key reason for using suitable lubricating-oil additives? (a) To improve selected oil properties such as oxidation or wear resistance under specified conditions (b) To eliminate the need for the correct oil grade (c) To substitute for every engine cooling component (d) To keep contaminated oil in service indefinitely
- A shaft supported on V-blocks shows a changing dial-indicator reading during rotation. What is most directly being assessed? (a) Chemical contamination of engine oil (b) The radial clearance inside the universal-joint bearings (c) Propeller-shaft run-out or straightness (d) Combustion chamber compression ratio
- Which of these is not a normal result to expect from a well-functioning ABS on a slippery road? (a) A brake-pedal pulsation during some ABS interventions (b) Improved opportunity to steer around an obstacle (c) Regulation of brake pressure when imminent lock is detected (d) Complete elimination of skidding risk regardless of tyres and conditions
- Before inspecting a rear axle assembly after a reported differential noise, what is an appropriate safety measure? (a) Rely on a hydraulic jack without any stand (b) Support the vehicle securely and follow the correct dismantling procedure (c) Spin the shaft while loose clothing is close to it (d) Remove wheel fasteners while the vehicle is unsupported
- Which claim about power-assisted steering is NOT justified? (a) It reduces the effort needed at the steering wheel (b) The hydraulic or electric system requires servicing as specified (c) A failure of assistance may make steering heavier (d) Assistance means the mechanical steering linkage can be ignored for safety
- When the fronts of the two wheels are closer together than the rears, the setting is called ________. (a) toe-in (b) kingpin inclination (c) negative camber (d) positive caster
- An electric fuel pump differs from an engine-driven mechanical pump chiefly in its ________. (a) responsibility for reducing exhaust sound (b) power source and independence from direct mechanical engine drive (c) ability to control combustion chamber temperature directly (d) method of raising engine fuel-injection pressure
- A driver reports heavy steering after a power-assist failure while the steering linkage remains intact. What explains the symptom? (a) The propeller shaft has become a fixed axle (b) ABS has automatically increased engine compression (c) The driver must supply more of the steering effort previously assisted by the system (d) The steering linkage no longer transmits any mechanical input
- A car tends to wander and its steering feels vague after front-end repairs. Which assessment is most relevant? (a) Replace the fuel pump without checking steering (b) Assume all front-end repairs automatically restore alignment (c) Replace the power-assist pump without assessing steering geometry (d) Inspect linkage play and check caster, toe and associated geometry
- Which statement does NOT accurately describe a turbine engine? (a) Rotating elements transfer energy to the shaft (b) It necessarily uses reciprocating pistons in cylinders to drive its main shaft (c) A continuous fluid flow acts on turbine stages (d) Its construction differs from a conventional piston engine
- An air-cooled engine overheats at low speed after cooling fins become clogged. Which explanation is most plausible? (a) Heat is removed primarily through transmission fluid (b) Blocked fins increase water-pump discharge pressure (c) Blocked fins increase the rate of airflow through the cooling passages (d) Blocked fins impede heat transfer to the surrounding air
- Which statement about anti-lock braking systems (ABS) is NOT accurate? (a) Wheel-speed information supports control of brake pressure (b) The system can help preserve steering control during emergency braking (c) ABS guarantees the shortest stopping distance on every road surface (d) ABS attempts to prevent sustained wheel lock
- The following may cause steering instability EXCEPT ________. (a) correctly maintained steering joints and specified wheel geometry (b) worn suspension components (c) excessive play in steering linkage (d) incorrect toe settings
- Which of these is not a reason a propeller shaft requires universal joints? (a) To accommodate changing driveline geometry (b) To transmit rotation between shafts at an angle (c) To maintain a permanently straight and rigid connection at all suspension positions (d) To allow articulation during axle movement
- A suspension strut leaks and the car bounces repeatedly after passing a road hump. Which repair focus is most defensible? (a) Increase tyre pressure above specification to substitute for damping (b) Inspect damping components and related suspension attachments (c) Replace a working silencer because it affects ride bounce (d) Ignore the leak because the spring is still present
- Compared with an air-cooled engine, a water-cooled engine typically depends more directly on ________. (a) a complete absence of coolant hoses and any radiator (b) unrestricted wheel camber (c) a permanently sealed cylinder head with no fins (d) a circulating coolant circuit and heat exchanger
- ________ links the steering wheels so their turning angles accommodate different paths through a corner. (a) Differential oil cooling (b) Ackermann steering geometry (c) Engine decarbonisation (d) Fuel-injection timing
- Why must engine mountings be inspected when investigating unusual chassis vibration? (a) Engine mountings regulate exhaust gas oxygen directly (b) Only tyre imbalance can create vibrations transmitted to the chassis (c) Worn mountings may transmit excessive engine movement and vibration to the frame (d) Engine mountings affect combustion timing but cannot transmit vibration
- The gearbox component that helps equalise the relative speeds of rotating parts during a gear change is the ________. (a) synchroniser (b) muffler (c) fuel strainer (d) engine mounting
- Which workflow best demonstrates competent suspension maintenance in a workshop? (a) Adjust unrelated engine firing order as a suspension repair (b) Inspect wear and mounting security, correct faults and verify operation under safe conditions (c) Check only the spring colour and omit road-holding verification (d) Replace every component without diagnosis and omit inspection
- A drivetrain shaft that transfers rotation from the gearbox toward the rear axle is the ________. (a) steering rack (b) oil strainer (c) stabiliser bar (d) propeller shaft
- Which statement best distinguishes understeer from oversteer? (a) Both are exactly the same as toe-in (b) Oversteer describes excessive front tyre slip with no rotation (c) Understeer means the vehicle turns less than commanded; oversteer tends to rotate it more (d) Understeer always means the rear tyres lose grip first
- The correct step in diagnosing gear grinding despite full clutch disengagement is to examine ________. (a) Synchroniser wear or inability to match gear speeds (b) A blocked exhaust tailpipe as the only possible cause (c) A broken horn switch (d) Excessive radiator coolant concentration
- An ABS warning light remains on after startup. Which response is appropriate? (a) Assume the warning can be cleared by permanently deactivating ABS (b) Assume the warning indicates stronger braking performance (c) Disconnect wheel-speed sensors without testing (d) Diagnose the fault with a suitable procedure and verify conventional braking operation
- The transmission component that uses fluid motion to transmit torque between rotating members is a ________. (a) disc brake (b) fluid flywheel (c) universal joint (d) propeller-shaft spline
- A replacement exhaust muffler has a severe internal blockage. What consequence is most plausible? (a) Restoration of worn suspension bushings (b) Automatic correction of ignition firing order (c) Excessive exhaust back-pressure and restricted engine performance (d) Reduction in propeller-shaft run-out
- Why does a vehicle with worn shock absorbers often show poorer road holding? (a) Wheel oscillation becomes less controlled, reducing reliable contact with the surface (b) The engine speed always rises during suspension travel (c) The rear axle stops rotating automatically (d) The camshaft ceases to open intake valves
- Which of these is not a legitimate objective of suspension-system maintenance? (a) To support controlled wheel contact with the road (b) To make road shocks pass without control directly to the vehicle body (c) To identify worn joints and dampers (d) To reduce undesirable oscillation
- Which of the following connections is most suitable when a chassis-mounted component must be removed routinely for servicing? (a) An unapproved adhesive bond (b) A permanent weld across the access point (c) A correctly specified bolted joint (d) A joint deliberately left loose
- Uneven tyre wear persists after tyre replacement; measurement shows the frame is distorted. What is the sound next action? (a) Compensate permanently by overinflating one tyre (b) Adjust wheel alignment without measuring the frame distortion (c) Assume the new tyres are the sole cause (d) Assess and correct chassis geometry before repeating wheel alignment
- ________ is the alignment condition that helps a chassis maintain the intended geometric relationship between its main components. (a) Uncontrolled frame twist (b) Correct chassis geometry (c) Excessive propeller-shaft run-out (d) Unequal tyre inflation
- Why does a fully floating axle arrangement generally reduce the wheel-supporting bending load on its drive shaft? (a) The wheel hub is supported by bearings while the shaft primarily transmits driving torque (b) It has no connection with an axle casing (c) The shaft must carry the full vehicle weight without a hub (d) It eliminates the need for wheel bearings entirely
- ________ is an exhaust-system component designed primarily to reduce emitted engine noise. (a) A synchroniser hub (b) A kingpin (c) A universal joint (d) A muffler
- Why can ABS help a driver steer during hard braking on many surfaces? (a) It removes all friction between tyre and road (b) It increases engine speed to turn front wheels (c) It reduces prolonged wheel lock so tyres can continue to generate lateral control (d) It mechanically changes Ackermann geometry while braking
- All these considerations matter when selecting a fuel pump EXCEPT ________. (a) the design of the vehicle’s seat upholstery (b) required fuel delivery (c) power supply or drive arrangement (d) operating pressure and compatibility
- Which function is shared by mechanical and electric fuel pumps in a suitable fuel system? (a) Preventing the fuel from reaching the carburettor or injection system (b) Delivering fuel from its supply to the engine at the required conditions (c) Suppressing exhaust noise by absorbing sound waves (d) Regulating the spark timing rather than delivering fuel
- In an engine with a triangular rotor revolving within a specially shaped housing, the operating principle is that of the ________ engine. (a) Wankel rotary (b) free-piston steam (c) inline reciprocating piston (d) single-cylinder diesel piston
SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.
1. Answer the following questions.
(a) A rear-wheel-drive vehicle vibrates increasingly with speed. Describe five diagnostic checks across the propeller shaft, universal joints and mountings. (5 marks)
(b) Explain five workshop precautions necessary before removing and inspecting transmission or rear-axle components. (5 marks)
2. Answer the following questions.
(a) Using suitable sketches if helpful, explain the roles of Ackermann linkage, camber, caster, toe and kingpin inclination in steering geometry. (5 marks)
(b) A car wanders and wears its front tyres rapidly. Propose five diagnostic steps to identify whether steering or suspension is responsible. (5 marks)
3. Answer the following questions.
(a) Analyse five differences or service considerations between air-cooled and water-cooled engine systems. (5 marks)
(b) Describe five reasons why proper fuel pump and muffler selection or maintenance affects engine performance or safety. (5 marks)
4. Answer the following questions.
(a) Explain how ABS detects and responds to impending wheel lock, identifying five elements of the operating sequence. (5 marks)
(b) Evaluate five claims or limitations associated with ABS, including the importance of tyre condition and road surface. (5 marks)
OBJECTIVE MARKING SCHEME
Question 1 – ✅ (c) The top of the wheel leans outward relative to its lower edge
Question 2 – ✅ (a) assuming every carbon deposit can be removed by increasing tyre pressure
Question 3 – ✅ (d) reduce tyre scrubbing as the wheels follow different turning radii
Question 4 – ✅ (a) To improve selected oil properties such as oxidation or wear resistance under specified conditions
Question 5 – ✅ (c) Propeller-shaft run-out or straightness
Question 6 – ✅ (d) Complete elimination of skidding risk regardless of tyres and conditions
Question 7 – ✅ (b) Support the vehicle securely and follow the correct dismantling procedure
Question 8 – ✅ (d) Assistance means the mechanical steering linkage can be ignored for safety
Question 9 – ✅ (a) toe-in
Question 10 – ✅ (b) power source and independence from direct mechanical engine drive
Question 11 – ✅ (c) The driver must supply more of the steering effort previously assisted by the system
Question 12 – ✅ (d) Inspect linkage play and check caster, toe and associated geometry
Question 13 – ✅ (b) It necessarily uses reciprocating pistons in cylinders to drive its main shaft
Question 14 – ✅ (d) Blocked fins impede heat transfer to the surrounding air
Question 15 – ✅ (c) ABS guarantees the shortest stopping distance on every road surface
Question 16 – ✅ (a) correctly maintained steering joints and specified wheel geometry
Question 17 – ✅ (c) To maintain a permanently straight and rigid connection at all suspension positions
Question 18 – ✅ (b) Inspect damping components and related suspension attachments
Question 19 – ✅ (d) a circulating coolant circuit and heat exchanger
Question 20 – ✅ (b) Ackermann steering geometry
Question 21 – ✅ (c) Worn mountings may transmit excessive engine movement and vibration to the frame
Question 22 – ✅ (a) synchroniser
Question 23 – ✅ (b) Inspect wear and mounting security, correct faults and verify operation under safe conditions
Question 24 – ✅ (d) propeller shaft
Question 25 – ✅ (c) Understeer means the vehicle turns less than commanded; oversteer tends to rotate it more
Question 26 – ✅ (a) Synchroniser wear or inability to match gear speeds
Question 27 – ✅ (d) Diagnose the fault with a suitable procedure and verify conventional braking operation
Question 28 – ✅ (b) fluid flywheel
Question 29 – ✅ (c) Excessive exhaust back-pressure and restricted engine performance
Question 30 – ✅ (a) Wheel oscillation becomes less controlled, reducing reliable contact with the surface
Question 31 – ✅ (b) To make road shocks pass without control directly to the vehicle body
Question 32 – ✅ (c) A correctly specified bolted joint
Question 33 – ✅ (d) Assess and correct chassis geometry before repeating wheel alignment
Question 34 – ✅ (b) Correct chassis geometry
Question 35 – ✅ (a) The wheel hub is supported by bearings while the shaft primarily transmits driving torque
Question 36 – ✅ (d) A muffler
Question 37 – ✅ (c) It reduces prolonged wheel lock so tyres can continue to generate lateral control
Question 38 – ✅ (a) the design of the vehicle’s seat upholstery
Question 39 – ✅ (b) Delivering fuel from its supply to the engine at the required conditions
Question 40 – ✅ (a) Wankel rotary
THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: Inspect run-out with V-block/dial indicator, joint wear, shaft balance, mounting security, alignment and bearing condition; any five 1 each.
(b) 5 marks: Secure vehicle, isolate drive, use stands and tools, manage fluids, mark positions/keep parts identified, follow manual; any five 1 each.
Question 2 (10 Marks)
(a) 5 marks: Five accurate distinct functions/definitions, 1 each.
(b) 5 marks: Check pressures/wear, alignment, linkage play, wheel bearings, ball joints, dampers; any five reasoned actions 1 each.
Question 3 (10 Marks)
(a) 5 marks: Heat transfer method, coolant/radiator, pump/hoses, airflow/fins, leak risks, maintenance requirements; five distinct correct 1 each.
(b) 5 marks: Correct delivery and pressure, reliable power drive, correct exhaust flow, noise reduction, heat/leak safety; five correct 1 each.
Question 4 (10 Marks)
(a) 5 marks: Wheel sensors, speed signals, controller analysis, hydraulic pressure modulation, continued wheel rotation/steering; 1 each.
(b) 5 marks: Steering control, lock prevention, surface-dependent stopping distance, grip limitations, warnings/fault diagnosis, proper tyres; any five 1 each.

Community Join the conversation Open discussion +