Skip to content
HeadTeacher.ng
Examinations

First Term Auto Mechanics Examination for SS 3

SSS 3 First Term Auto Mechanics examination covering chassis, engine, transmission. Includes 40 objective questions, theory and marking schemes.

Published Reading15 min Comments0

Class: SSS 3
Term: First Term
Subject: Auto Mechanics
Time: 2 Hours 30 Minutes
Total Marks: 70


SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.

  1. Which claim about power steering is NOT supported by the safety requirements of its mechanical linkage? (a) A failure of assistance may make steering heavier    (b) The hydraulic or electric system requires servicing as specified    (c) Assistance means the mechanical steering linkage can be ignored for safety    (d) It reduces the effort needed at the steering wheel
  2. When comparing electrical and mechanically driven fuel delivery units, their main constructional difference lies in the ________. (a) method of raising engine fuel-injection pressure    (b) power source and independence from direct mechanical engine drive    (c) ability to control combustion chamber temperature directly    (d) responsibility for reducing exhaust sound
  3. All of these should affect a fuel-pump replacement specification EXCEPT ________. (a) required fuel delivery    (b) power supply or drive arrangement    (c) operating pressure and compatibility    (d) the design of the vehicle’s seat upholstery
  4. The ABS indicator stays illuminated and a diagnostic scan records a wheel-speed sensor issue. What should be done? (a) Assume the warning indicates stronger braking performance    (b) Diagnose the fault with a suitable procedure and verify conventional braking operation    (c) Assume the warning can be cleared by permanently deactivating ABS    (d) Disconnect wheel-speed sensors without testing
  5. In an emergency stop on a wet road, why may an anti-lock system help a driver retain directional control? (a) It increases engine speed to turn front wheels    (b) It removes all friction between tyre and road    (c) It reduces prolonged wheel lock so tyres can continue to generate lateral control    (d) It mechanically changes Ackermann geometry while braking
  6. An air-cooled cylinder head has accumulated dirt between its cooling fins. Which thermal consequence should be anticipated? (a) Blocked fins impede heat transfer to the surrounding air    (b) Blocked fins increase water-pump discharge pressure    (c) Heat is removed primarily through transmission fluid    (d) Blocked fins increase the rate of airflow through the cooling passages
  7. After a non-original silencer is fitted, exhaust back-pressure becomes abnormally high. Which engine-performance effect is most plausible? (a) Restoration of worn suspension bushings    (b) Excessive exhaust back-pressure and restricted engine performance    (c) Automatic correction of ignition firing order    (d) Reduction in propeller-shaft run-out
  8. When assessing air and liquid cooling designs, the liquid-cooled system is more directly dependent on ________. (a) a circulating coolant circuit and heat exchanger    (b) unrestricted wheel camber    (c) a complete absence of coolant hoses and any radiator    (d) a permanently sealed cylinder head with no fins
  9. A fleet manager compares oils containing different additive packages. What is a defensible reason for selecting suitable additives? (a) To eliminate the need for the correct oil grade    (b) To keep contaminated oil in service indefinitely    (c) To improve selected oil properties such as oxidation or wear resistance under specified conditions    (d) To substitute for every engine cooling component
  10. A vehicle can still be steered after assistance is lost but the steering wheel becomes very heavy. Which interpretation best explains this? (a) The driver must supply more of the steering effort previously assisted by the system    (b) The propeller shaft has become a fixed axle    (c) ABS has automatically increased engine compression    (d) The steering linkage no longer transmits any mechanical input
  11. ________ enables engineers to confirm that the main chassis members retain the intended alignment after structural repair. (a) Excessive propeller-shaft run-out    (b) Unequal tyre inflation    (c) Uncontrolled frame twist    (d) Correct chassis geometry
  12. The torque-transmitting coupling that transfers motion through a working fluid rather than a direct rigid connection is a ________. (a) disc brake    (b) fluid flywheel    (c) propeller-shaft spline    (d) universal joint
  13. A propeller shaft is removed after severe vibration. A workshop mounts it on V-blocks and turns it beneath a dial gauge. Which property is measured? (a) Propeller-shaft run-out or straightness    (b) Chemical contamination of engine oil    (c) The radial clearance inside the universal-joint bearings    (d) Combustion chamber compression ratio
  14. Which of the following is not a legitimate performance objective of an automotive suspension? (a) To identify worn joints and dampers    (b) To support controlled wheel contact with the road    (c) To make road shocks pass without control directly to the vehicle body    (d) To reduce undesirable oscillation
  15. In a fully floating rear-axle arrangement, which design feature helps separate the wheel-bearing load from the drive-shaft function? (a) It has no connection with an axle casing    (b) It eliminates the need for wheel bearings entirely    (c) The shaft must carry the full vehicle weight without a hub    (d) The wheel hub is supported by bearings while the shaft primarily transmits driving torque
  16. After a suspension overhaul, a car wanders at speed even though the power steering operates. Which technical investigation is most appropriate? (a) Replace the fuel pump without checking steering    (b) Inspect linkage play and check caster, toe and associated geometry    (c) Replace the power-assist pump without assessing steering geometry    (d) Assume all front-end repairs automatically restore alignment
  17. All these can justify an engine decarbonisation investigation EXCEPT ________. (a) evidence of deposit accumulation    (b) appropriate workshop cleaning and safety procedures    (c) assuming every carbon deposit can be removed by increasing tyre pressure    (d) engine condition and operating symptoms
  18. A rear-axle differential is to be dismantled for inspection. Which initial safety action should take priority? (a) Rely on a hydraulic jack without any stand    (b) Spin the shaft while loose clothing is close to it    (c) Remove wheel fasteners while the vehicle is unsupported    (d) Support the vehicle securely and follow the correct dismantling procedure
  19. After a collision, all four wheels are aligned but a vehicle still tracks diagonally. Inspection suggests permanent frame deformation. What must the technician assess before further adjustment? (a) Compensate permanently by overinflating one tyre    (b) Assume the new tyres are the sole cause    (c) Assess and correct chassis geometry before repeating wheel alignment    (d) Adjust wheel alignment without measuring the frame distortion
  20. Which of these is not an outcome that can be guaranteed simply by fitting ABS to a vehicle? (a) A brake-pedal pulsation during some ABS interventions    (b) Complete elimination of skidding risk regardless of tyres and conditions    (c) Regulation of brake pressure when imminent lock is detected    (d) Improved opportunity to steer around an obstacle
  21. Which assertion about turbine operation is NOT consistent with its rotating energy-conversion principle? (a) A continuous fluid flow acts on turbine stages    (b) Its construction differs from a conventional piston engine    (c) Rotating elements transfer energy to the shaft    (d) It necessarily uses reciprocating pistons in cylinders to drive its main shaft
  22. ________ is installed in an exhaust line to attenuate sound generated by the engine. (a) A muffler    (b) A universal joint    (c) A kingpin    (d) A synchroniser hub
  23. ________ uses a rotor turning within a specially profiled housing rather than reciprocating pistons. (a) inline reciprocating piston    (b) single-cylinder diesel piston    (c) free-piston steam    (d) Wankel rotary
  24. Which of the following detachable connections is the most suitable for a routinely serviced chassis bracket? (a) A joint deliberately left loose    (b) A correctly specified bolted joint    (c) A permanent weld across the access point    (d) An unapproved adhesive bond
  25. Which of these is not a valid design purpose of the universal joints in a conventional articulated driveline? (a) To accommodate changing driveline geometry    (b) To transmit rotation between shafts at an angle    (c) To allow articulation during axle movement    (d) To maintain a permanently straight and rigid connection at all suspension positions
  26. The gear-changing component intended to match rotating speeds before the gear teeth engage is the ________. (a) synchroniser    (b) fuel strainer    (c) muffler    (d) engine mounting
  27. Which statement concerning vehicle anti-lock braking is NOT supported under all road-surface conditions? (a) The system can help preserve steering control during emergency braking    (b) ABS attempts to prevent sustained wheel lock    (c) ABS guarantees the shortest stopping distance on every road surface    (d) Wheel-speed information supports control of brake pressure
  28. After a road impact, a corner of the car continues oscillating and the damper is wet with oil. Which system should receive primary attention? (a) Inspect damping components and related suspension attachments    (b) Ignore the leak because the spring is still present    (c) Increase tyre pressure above specification to substitute for damping    (d) Replace a working silencer because it affects ride bounce
  29. The rotating member linking a rear-wheel-drive gearbox output with the rear final drive is the ________. (a) stabiliser bar    (b) propeller shaft    (c) steering rack    (d) oil strainer
  30. During a road test, a worn damper permits repeated body oscillation and tyre hop. Why does this threaten handling? (a) The camshaft ceases to open intake valves    (b) The rear axle stops rotating automatically    (c) The engine speed always rises during suspension travel    (d) Wheel oscillation becomes less controlled, reducing reliable contact with the surface
  31. ________ permits steered wheels to follow the different radii required when a vehicle negotiates a corner. (a) Ackermann steering geometry    (b) Engine decarbonisation    (c) Differential oil cooling    (d) Fuel-injection timing
  32. An engine shakes noticeably at idle although the wheels are stationary. Why should its chassis mountings be included in the diagnosis? (a) Only tyre imbalance can create vibrations transmitted to the chassis    (b) Engine mountings affect combustion timing but cannot transmit vibration    (c) Engine mountings regulate exhaust gas oxygen directly    (d) Worn mountings may transmit excessive engine movement and vibration to the frame
  33. Which workshop procedure best demonstrates systematic fault prevention in suspension servicing? (a) Adjust unrelated engine firing order as a suspension repair    (b) Inspect wear and mounting security, correct faults and verify operation under safe conditions    (c) Check only the spring colour and omit road-holding verification    (d) Replace every component without diagnosis and omit inspection
  34. Which observation indicates positive camber rather than positive caster or toe-in? (a) The front edges of both tyres point closer together    (b) The wheel rotates faster than the axle    (c) The top of the wheel leans outward relative to its lower edge    (d) The steering axis is vertical by definition
  35. A technician compares the motion of a car that pushes wide at a bend with another whose rear rotates excessively. Which distinction is accurate? (a) Understeer always means the rear tyres lose grip first    (b) Both are exactly the same as toe-in    (c) Oversteer describes excessive front tyre slip with no rotation    (d) Understeer means the vehicle turns less than commanded; oversteer tends to rotate it more
  36. All of the following are potential sources of poor directional stability EXCEPT ________. (a) incorrect toe settings    (b) excessive play in steering linkage    (c) correctly maintained steering joints and specified wheel geometry    (d) worn suspension components
  37. The correct step in investigating repeated grinding during gearbox engagement is to check for ________. (a) Synchroniser wear or inability to match gear speeds    (b) A blocked exhaust tailpipe as the only possible cause    (c) A broken horn switch    (d) Excessive radiator coolant concentration
  38. Which responsibility is common to mechanical and electrically powered petrol pumps? (a) Regulating the spark timing rather than delivering fuel    (b) Delivering fuel from its supply to the engine at the required conditions    (c) Suppressing exhaust noise by absorbing sound waves    (d) Preventing the fuel from reaching the carburettor or injection system
  39. The wheel-setting term for front tyre edges being closer together than their rear edges is ________. (a) kingpin inclination    (b) positive caster    (c) toe-in    (d) negative camber
  40. The main reason for providing different front-wheel angles during cornering is to ________. (a) reduce tyre scrubbing as the wheels follow different turning radii    (b) keep both wheels on exactly the same circular path    (c) avoid any need for suspension travel    (d) increase the engine firing order

SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.

1. Answer the following questions.
(a) A driver reports speed-related driveline shudder after a rear-axle repair. Outline five measurements or inspections that can identify the source. (5 marks)
(b) Propose five actions to ensure safe dismantling, inspection and assembly of a rear-wheel-drive transmission. (5 marks)

2. Answer the following questions.
(a) Evaluate five aspects of steering geometry that could account for persistent tyre scrubbing and poor directional stability. (5 marks)
(b) A vehicle bounces after bumps and pulls on uneven pavement. Describe five independent suspension-related faults or checks. (5 marks)

3. Answer the following questions.
(a) Compare five service requirements of engine air-cooling and liquid-cooling arrangements. (5 marks)
(b) Discuss five ways faulty fuel delivery or restricted muffler flow can contribute to poor performance. (5 marks)

4. Answer the following questions.
(a) Explain five operating functions of a typical ABS using sensors, controller and brake-pressure modulation. (5 marks)
(b) A vehicle’s ABS warning lamp remains on. Describe five safe diagnostic actions or precautions before release for use. (5 marks)


OBJECTIVE MARKING SCHEME
Question 1 – ✅ (c) Assistance means the mechanical steering linkage can be ignored for safety
Question 2 – ✅ (b) power source and independence from direct mechanical engine drive
Question 3 – ✅ (d) the design of the vehicle’s seat upholstery
Question 4 – ✅ (b) Diagnose the fault with a suitable procedure and verify conventional braking operation
Question 5 – ✅ (c) It reduces prolonged wheel lock so tyres can continue to generate lateral control
Question 6 – ✅ (a) Blocked fins impede heat transfer to the surrounding air
Question 7 – ✅ (b) Excessive exhaust back-pressure and restricted engine performance
Question 8 – ✅ (a) a circulating coolant circuit and heat exchanger
Question 9 – ✅ (c) To improve selected oil properties such as oxidation or wear resistance under specified conditions
Question 10 – ✅ (a) The driver must supply more of the steering effort previously assisted by the system
Question 11 – ✅ (d) Correct chassis geometry
Question 12 – ✅ (b) fluid flywheel
Question 13 – ✅ (a) Propeller-shaft run-out or straightness
Question 14 – ✅ (c) To make road shocks pass without control directly to the vehicle body
Question 15 – ✅ (d) The wheel hub is supported by bearings while the shaft primarily transmits driving torque
Question 16 – ✅ (b) Inspect linkage play and check caster, toe and associated geometry
Question 17 – ✅ (c) assuming every carbon deposit can be removed by increasing tyre pressure
Question 18 – ✅ (d) Support the vehicle securely and follow the correct dismantling procedure
Question 19 – ✅ (c) Assess and correct chassis geometry before repeating wheel alignment
Question 20 – ✅ (b) Complete elimination of skidding risk regardless of tyres and conditions
Question 21 – ✅ (d) It necessarily uses reciprocating pistons in cylinders to drive its main shaft
Question 22 – ✅ (a) A muffler
Question 23 – ✅ (d) Wankel rotary
Question 24 – ✅ (b) A correctly specified bolted joint
Question 25 – ✅ (d) To maintain a permanently straight and rigid connection at all suspension positions
Question 26 – ✅ (a) synchroniser
Question 27 – ✅ (c) ABS guarantees the shortest stopping distance on every road surface
Question 28 – ✅ (a) Inspect damping components and related suspension attachments
Question 29 – ✅ (b) propeller shaft
Question 30 – ✅ (d) Wheel oscillation becomes less controlled, reducing reliable contact with the surface
Question 31 – ✅ (a) Ackermann steering geometry
Question 32 – ✅ (d) Worn mountings may transmit excessive engine movement and vibration to the frame
Question 33 – ✅ (b) Inspect wear and mounting security, correct faults and verify operation under safe conditions
Question 34 – ✅ (c) The top of the wheel leans outward relative to its lower edge
Question 35 – ✅ (d) Understeer means the vehicle turns less than commanded; oversteer tends to rotate it more
Question 36 – ✅ (c) correctly maintained steering joints and specified wheel geometry
Question 37 – ✅ (a) Synchroniser wear or inability to match gear speeds
Question 38 – ✅ (b) Delivering fuel from its supply to the engine at the required conditions
Question 39 – ✅ (c) toe-in
Question 40 – ✅ (a) reduce tyre scrubbing as the wheels follow different turning radii


THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: Run-out on V-block/dial indicator, universal-joint play, bearing condition, shaft alignment and fastener/mount security; five 1 each.
(b) 5 marks: Secure vehicle, isolate drive, support components, use proper lifting/tools, note alignment and torque specs, check lubricant/leaks; five 1 each.
Question 2 (10 Marks)
(a) 5 marks: Ackermann geometry, camber, caster, toe, kingpin inclination or worn linkage; accurate role and effects 1 each.
(b) 5 marks: Damping/leaks, springs, bushes, ball joints, wheel bearings, wheel alignment, mounts; any five 1 each.
Question 3 (10 Marks)
(a) 5 marks: Fins/airflow, coolant, pump, radiator, hose leaks, temperature control and maintenance; five 1 each.
(b) 5 marks: Flow/pressure deficits, power supply issues, fuel contamination, exhaust back-pressure, noise/heat problems; any five 1 each.
Question 4 (10 Marks)
(a) 5 marks: Wheel-speed sensing, imminent lock detection, ECU, hydraulic modulation, retention of rotation and steerability; five 1 each.
(b) 5 marks: Read faults, check sensors/connectors, verify conventional braking, inspect hydraulic components, repair and test; any five 1 each.

Export this post
First Term Auto Mechanics Examination for SS 3
About the author

Royal Alikor

Royal Alikor is an educator with six years of classroom teaching and three years of elementary school leadership experience. He develops and reviews practical, curriculum-aligned learning materials for Nigerian schools.

Community Join the conversation Open discussion +