Class: SSS 3
Term: Second Term
Subject: Auto Mechanic Work
Time: 2 Hours 30 Minutes
Total Marks: 70
SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.
- The correct step in handling a vehicle with worn tyres and a braking complaint is to ________. (a) Carry out a high-speed test before any inspection (b) Change only the tyre valve caps (c) Balance the wheels and ignore the brake complaint (d) Assess braking safety, inspect tyres and document appropriate repairs before road release
- A customer reports that brakes fade during repeated downhill stops. Which diagnosis should the technician investigate? (a) A broken aerial cable (b) A change in vehicle number-plate colour (c) Overheated braking components and the condition of pads, discs or drums (d) A slight change in tyre pressure unrelated to temperature history
- ________ is the brake-fault symptom in which a pedal gradually sinks while steady pressure is applied. (a) Pedal creep (b) Static imbalance (c) Toe-out (d) Wheel eccentricity
- What is the principal value of performing brake checks after corrective work? (a) To avoid recording the repair performed (b) To establish that all unrelated components are new (c) To verify that safe and balanced braking has actually been restored (d) To demonstrate that brake-fluid type never matters
- The following are reasonable considerations before opening an automobile service enterprise EXCEPT ________. (a) likely customer demand (b) availability of qualified technicians (c) equipment and training costs (d) assuming specialist tools and safety procedures are unnecessary
- Which service package best matches a steering workshop’s declared specialist scope? (a) Servicing wheel bearings without assessing steering linkage play (b) Inspecting linkage play, wheel geometry and power-assist condition (c) Performing garment embroidery and textile grading (d) Balancing tyres without inspecting front wheel alignment
- A wire wheel differs from a pressed steel disc wheel chiefly through its ________. (a) spoked load-transferring structure rather than a pressed disc construction (b) ability to tolerate all spoke tension errors (c) a solid cast disc without load-carrying spokes (d) ability to function without tyre inflation
- A customer disputes a repair invoice, but the workshop has detailed findings, authorised work and part records. Which business principle is illustrated? (a) A receipt proves no technical mistake is possible (b) Service records prevent every disagreement automatically (c) Technical diagnosis should be replaced by marketing (d) Documentation supports transparent customer relations and dispute resolution
- Why can a workshop offering brake services face more serious liability when it omits final testing? (a) Undetected faults in safety-critical components may put road users at risk (b) Liability is determined solely by the size of the workshop (c) Brake safety is unrelated to customer trust (d) Final checks are needed only for cosmetic repairs
- Which of the following symptoms most strongly suggests unequal braking effort from side to side? (a) A seat belt retracts slowly (b) The brake warning light goes out during a routine self-check (c) The vehicle pulls to one side when the brakes are applied (d) The radio loses reception under acceleration
- Which ownership decision most directly improves a specialised brake-repair enterprise’s technical reliability? (a) Using unverified brake parts to minimise every invoice (b) Investing in suitable diagnostics, trained staff and quality control (c) Advertising guaranteed repairs without inspection (d) Replacing customer records with verbal estimates only
- New balancing weights fall off soon after fitting. Which factor should the technician assess? (a) The quality of contact between weight and rim (b) Exhaust manifold pressure (c) Weight retention and correct wheel-surface preparation (d) The vehicle’s fuel octane rating
- A brake technician finds reduced hydraulic pressure from damaged lines. The appropriate remedy requires locating and repairing the ________. (a) leak (b) surface temperature of the disc rotor (c) tyre tread pattern (d) hydraulic master-cylinder clearance
- Which statement about tyre interchange or rotation is NOT safe as a general rule? (a) Different tyre constructions may impose rotation restrictions (b) Tyre rotation may promote more even wear when appropriate (c) Tyre pressure and condition should be checked during rotation (d) Directional tyres can be swapped to either side regardless of their marked rotation
- A tyre wears rapidly at one shoulder despite repeated balancing. What limitation should the technician recognise? (a) A wheel cannot be aligned after balancing (b) Balancing cannot by itself correct wheel alignment or suspension faults (c) An imbalance must be the only cause of uneven shoulder wear (d) Wheel alignment is determined by balancing weights alone
- A vehicle vibrates at 85 km/h but not while stationary; its tyres have just been fitted. Which test is most relevant first? (a) Check wheel/tyre balance and fitment (b) Bleed the clutch only (c) Replace the exhaust silencer (d) Change brake-pad compounds without checking wheel rotational imbalance
- Which of these is not the main aim of dynamic wheel balancing? (a) To address side-to-side couple imbalance (b) To reduce speed-related wheel vibration (c) To remove excessive play in a steering ball joint (d) To reduce imbalance about the rotating wheel axis
- A potential vulcanising-business owner is preparing a start-up budget. Which order is most responsible? (a) Purchase all equipment before checking demand or premises (b) Estimate expected demand, costs, equipment and cash requirements before committing resources (c) Set prices without calculating costs (d) Ignore maintenance and consumables after opening
- The main reason for repairing a brake-fluid leak before road testing is that ________. (a) The leak always improves pedal modulation (b) It necessarily reduces fuel consumption (c) Brake fluid directly balances wheel rims (d) Loss of hydraulic pressure can compromise reliable stopping
- A rim made by pressing sheet steel into a wheel disc is a ________. (a) wire-spoked wheel (b) cast aluminium wheel (c) pressed steel disc wheel (d) forged piston
- A driver reports grinding at a wheel during braking. Which response is most appropriate? (a) Inspect the brake friction components and related hardware before further normal use (b) Increase engine speed to mask the noise (c) Adjust only the parking-brake cable without inspecting the noisy wheel (d) Rebalance the tyre without examining the brake assembly
- Which practical check best distinguishes a brake-system fault from tyre imbalance? (a) Assume every brake noise is caused by tyre tread irregularities (b) Assume any steering vibration comes from brake fluid (c) Replace both components without examination (d) Observe brake-pedal behaviour and braking response separately from speed-dependent wheel vibration
- All of the following can indicate a braking fault EXCEPT ________. (a) visible loss of brake fluid (b) a properly responsive pedal and equal braking under controlled test conditions (c) unusual grinding during braking (d) abnormally long stopping distance
- ________ occurs when the braking force repeatedly weakens because friction components become excessively hot. (a) Toe-in (b) Static balance (c) Brake fade (d) Wheel rotation
- A proprietor chooses to specialise in steering repairs rather than all vehicle work. Which advantage could justify the choice? (a) Only general workshops need safety rules (b) Focused training and tools may support higher competence in that service (c) Steering repairs cannot require spare parts (d) Specialisation eliminates all customer demand risk
- After a hydraulic brake-line repair, the brake pedal remains spongy. Which correction is most directly indicated? (a) Bleed the system correctly and inspect for leaks (b) Adjust the steering caster without examining hydraulics (c) Add extra tyre-balancing weights (d) Replace all wheels with wire spokes
- Compared with a pressed steel wheel, a light-alloy wheel is often selected because of ________. (a) a guaranteed absence of damage from impacts (b) automatic elimination of tyre inflation (c) the removal of any need for impact inspection after an accident (d) lower unsprung mass potential and different design or heat-transfer characteristics
- A steering-service shop has skilled labour but no equipment for checking alignment. What business risk is most obvious? (a) A shortage of advertising slogans alone (b) A shortage of customers willing to request documented inspection (c) Incorrect or unverified repair decisions may undermine service quality (d) An inability to demonstrate service quality with test results
- Why should a brake or suspension enterprise maintain service records and parts invoices? (a) They support traceability, customer trust and accountability for the work performed (b) They guarantee that no future fault can occur (c) They make technician competence irrelevant (d) They remove the need for quality testing
- All these factors should influence tyre-balance diagnosis EXCEPT ________. (a) tyre and rim physical damage (b) run-out and correct wheel fitment (c) wheel mass distribution (d) the supplier’s preferred colour for workshop paint
- A wheel assembly that is heavy at one point may require ________ balancing to reduce vibration caused by uneven mass distribution. (a) steering-rack (b) static (c) fuel-system (d) hydraulic
- After balancing, a vibration remains and a rim has visible distortion. What should the technician infer? (a) A damaged wheel may require repair or replacement; weights alone cannot correct structural distortion (b) Any vibration proves brake-fluid contamination (c) Additional weights always restore a severely bent rim (d) Wheel condition cannot cause vehicle vibration
- Which conclusion does NOT follow from a pedal that travels unusually far? (a) Fluid loss may need examination (b) A full brake-system diagnosis may be necessary (c) Air or adjustment may require checking (d) The cause must always be a wheel-balancing error
- Which of these is not a sound advantage to claim for a tyre-balancing service? (a) It can improve ride smoothness at speed (b) It may reduce vibration-related discomfort (c) It cures all brake-hydraulic faults without diagnosis (d) It can address imbalance after tyre replacement
- A workshop concentrating on puncture repairs, tyre fitting and related services is a ________ enterprise. (a) engine-casting (b) vulcanising (c) vehicle upholstery (d) steering-rack manufacture
- Which distinction between tyre balancing and wheel alignment is most accurate? (a) Alignment is needed only for wire wheels (b) Both processes correct brake fluid contamination (c) Balancing can repair bent suspension arms (d) Balancing corrects rotating mass distribution; alignment sets wheel orientation angles
- ________ describes the brake-pedal feel commonly associated with air trapped in a hydraulic braking system. (a) A fixed pedal with no travel (b) A spongy pedal (c) A steering return (d) A tyre-balance vibration
- Which of these is not a valid basis for tyre interchange decisions? (a) The assumption that tyres of different sizes and constructions are always interchangeable (b) Directional markings and wheel positions (c) Manufacturer rotation guidance (d) Tyre wear and condition
- When balance correction must account for different mass distributions across the inner and outer wheel planes, the technique is ________. (a) clutch synchronising (b) static toe adjustment (c) dynamic balancing (d) hydraulic bleeding
- Which approach is NOT an acceptable remedy for a hydraulic brake fault? (a) Repairing leaks before testing (b) Filling the system with an unidentified liquid that happens to be available (c) Removing trapped air by proper bleeding (d) Using the specified brake fluid
SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.
1. Answer the following questions.
(a) A vehicle has a spongy pedal after brake-line work. Describe five diagnostic or corrective actions before the vehicle returns to service. (5 marks)
(b) Distinguish five symptoms of brake faults and the likely system areas that should be examined for each. (5 marks)
2. Answer the following questions.
(a) Compare static and dynamic wheel balancing with five relevant features or uses. (5 marks)
(b) Explain five checks that should accompany tyre rotation after fitting or balancing. (5 marks)
3. Answer the following questions.
(a) Compare the advantages and operational limitations of a vulcanising business and a specialised brake-repair business in five points. (5 marks)
(b) Develop five budget headings for a new vehicle-service enterprise and explain why each matters. (5 marks)
4. Answer the following questions.
(a) A workshop receives repeated complaints after steering repairs. Analyse five changes to its technical and customer-service procedures. (5 marks)
(b) Explain five safety or quality reasons to use suitable parts and inspect braking components before a test drive. (5 marks)
OBJECTIVE MARKING SCHEME
Question 1 – ✅ (d) Assess braking safety, inspect tyres and document appropriate repairs before road release
Question 2 – ✅ (c) Overheated braking components and the condition of pads, discs or drums
Question 3 – ✅ (a) Pedal creep
Question 4 – ✅ (c) To verify that safe and balanced braking has actually been restored
Question 5 – ✅ (d) assuming specialist tools and safety procedures are unnecessary
Question 6 – ✅ (b) Inspecting linkage play, wheel geometry and power-assist condition
Question 7 – ✅ (a) spoked load-transferring structure rather than a pressed disc construction
Question 8 – ✅ (d) Documentation supports transparent customer relations and dispute resolution
Question 9 – ✅ (a) Undetected faults in safety-critical components may put road users at risk
Question 10 – ✅ (c) The vehicle pulls to one side when the brakes are applied
Question 11 – ✅ (b) Investing in suitable diagnostics, trained staff and quality control
Question 12 – ✅ (c) Weight retention and correct wheel-surface preparation
Question 13 – ✅ (a) leak
Question 14 – ✅ (d) Directional tyres can be swapped to either side regardless of their marked rotation
Question 15 – ✅ (b) Balancing cannot by itself correct wheel alignment or suspension faults
Question 16 – ✅ (a) Check wheel/tyre balance and fitment
Question 17 – ✅ (c) To remove excessive play in a steering ball joint
Question 18 – ✅ (b) Estimate expected demand, costs, equipment and cash requirements before committing resources
Question 19 – ✅ (d) Loss of hydraulic pressure can compromise reliable stopping
Question 20 – ✅ (c) pressed steel disc wheel
Question 21 – ✅ (a) Inspect the brake friction components and related hardware before further normal use
Question 22 – ✅ (d) Observe brake-pedal behaviour and braking response separately from speed-dependent wheel vibration
Question 23 – ✅ (b) a properly responsive pedal and equal braking under controlled test conditions
Question 24 – ✅ (c) Brake fade
Question 25 – ✅ (b) Focused training and tools may support higher competence in that service
Question 26 – ✅ (a) Bleed the system correctly and inspect for leaks
Question 27 – ✅ (d) lower unsprung mass potential and different design or heat-transfer characteristics
Question 28 – ✅ (c) Incorrect or unverified repair decisions may undermine service quality
Question 29 – ✅ (a) They support traceability, customer trust and accountability for the work performed
Question 30 – ✅ (d) the supplier’s preferred colour for workshop paint
Question 31 – ✅ (b) static
Question 32 – ✅ (a) A damaged wheel may require repair or replacement; weights alone cannot correct structural distortion
Question 33 – ✅ (d) The cause must always be a wheel-balancing error
Question 34 – ✅ (c) It cures all brake-hydraulic faults without diagnosis
Question 35 – ✅ (b) vulcanising
Question 36 – ✅ (d) Balancing corrects rotating mass distribution; alignment sets wheel orientation angles
Question 37 – ✅ (b) A spongy pedal
Question 38 – ✅ (a) The assumption that tyres of different sizes and constructions are always interchangeable
Question 39 – ✅ (c) dynamic balancing
Question 40 – ✅ (b) Filling the system with an unidentified liquid that happens to be available
THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: Check leakage, specified fluid, bleed system, assess flexible lines/master cylinder, safe operational test; five 1 each.
(b) 5 marks: Pulling/unequal action, grinding/pads, fluid loss/hydraulics, fade/heat, sinking pedal/leaks/internal bypass, pulsation/rotor; any five matched 1 each.
Question 2 (10 Marks)
(a) 5 marks: Single-plane vs two-plane, radial imbalance vs couple, equipment, expected vibration, corrective weights; five accurate comparisons 1 each.
(b) 5 marks: Pressure, tread/wear, rim damage, fitment, directional marking, vehicle guidance and torque; any five 1 each.
Question 3 (10 Marks)
(a) 5 marks: Demand, equipment, technical training, safety risk, stock, revenue and competition; five valid comparisons 1 each.
(b) 5 marks: Premises, equipment, inventory, wages, utilities, marketing, contingencies; five 1 each.
Question 4 (10 Marks)
(a) 5 marks: Inspection protocol, suitable tools, trained staff, test/quality check, records, warranty communication; five explained 1 each.
(b) 5 marks: Prevent failure, proper compatibility, avoid brake fade/pull, reliable hydraulic operation, technician/public safety; five 1 each.

Community Join the conversation Open discussion +