Skip to content
HeadTeacher.ng
Examinations

First Term Electrical Installation and Maintenance Work Examination for SS 3

First Term Electrical Installation and Maintenance Work Examination for SS 3. This SS 3 lesson follows the scheme of work.

Published Reading14 min Comments0

Class: SSS 3
Term: First Term
Subject: Electrical Installation and Maintenance Work
Time: 2 Hours 30 Minutes
Total Marks: 70


SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.

  1. ________ is appropriate after a workshop electrical accident once the casualty is safe and urgent care is arranged. (a) Recording the circumstances and reporting the incident    (b) Concealing the damaged supply cable    (c) Deleting the incident from the safety log    (d) Returning the faulty equipment to service without inspection
  2. A continuity test passes, yet winding insulation may still be unsafe. The strongest conclusion is that ________. (a) a conductive path guarantees sound insulation    (b) an ohmmeter confirms every mechanical alignment    (c) continuity does not replace insulation resistance and earthing checks    (d) a passed continuity test proves the starter is correctly sized
  3. The main reason wire gauge must be selected carefully during rewinding is that ________. (a) conductor cross-section affects resistance, heating and current capacity    (b) every wire of the same colour has the same rating    (c) number of turns is irrelevant to the motor    (d) only the coil’s external varnish matters
  4. The correct step when an installed motor repeatedly trips on starting is to ________. (a) bypass the protective device to keep it running    (b) replace the earth conductor with a smaller wire    (c) increase the fuse rating at random    (d) inspect load, starter, protective settings and supply conditions before restarting
  5. Which action does NOT belong in the safe response to a suspected electrical shock? (a) Calling for emergency help as needed    (b) Touching the casualty before the supply is made safe    (c) Assessing the casualty only when the scene is safe    (d) Recording the accident after the immediate emergency
  6. An armature shows excessive sparking after repair. Which of the following warrants inspection? (a) Commutator surface, brushes and the repaired coil connections    (b) Only the paint label attached to the rotor    (c) The number of people who attended a workshop seminar    (d) The brand name of the tool chest
  7. The ________ in a conventional DC machine helps reverse armature connections at appropriate positions. (a) fixed belt pulley    (b) cable gland    (c) commutator    (d) terminal fuse
  8. A coil must be rewound to reproduce the motor’s original performance. Which data are especially important? (a) Colour of the paint on the workshop wall    (b) Only the external shape of the terminal box    (c) number of unused terminal labels in the store    (d) Number of turns, conductor size and connection arrangement
  9. The ________ determines how winding coils are arranged and interconnected around an armature. (a) motor inspection date on the maintenance docket    (b) winding diagram    (c) sales description of the service package    (d) motor nameplate lettering style
  10. Which of the following is a key benefit of using an appropriate data cable type? (a) A guarantee of unlimited distance with no losses    (b) Complete removal of the need for termination checks    (c) Reliable transfer of the intended signals under the specified conditions    (d) Automatic repair of damaged insulation
  11. A battery is intended for repeated charging and discharging. Its most relevant classification is ________. (a) single-use primary cell    (b) static electrical resistor    (c) mechanical commutator    (d) secondary cell
  12. All these are reasonable items in a rewinding workshop budget except ________. (a) insulating materials    (b) the customer’s preferred brand name on an unrelated advert    (c) labour costs    (d) equipment maintenance
  13. The ________ of conductors is important when selecting them for load and installation conditions. (a) current-carrying capacity and insulation suitability    (b) appearance of the conductor’s outer sheath alone    (c) colour of the conductor reel alone    (d) manufacturer’s logo on the terminal cover
  14. Which action does NOT meet careful conductor-terminal practice? (a) Using secure connections    (b) Insulating accessible live metal    (c) Selecting a suitable termination method    (d) Leaving exposed loose strands that may bridge adjacent terminals
  15. The ________ should be compared against predicted revenue when deciding whether a small repair shop can service a loan. (a) the customer’s unrelated household spending    (b) repayment obligations and operating cash flow    (c) amount budgeted for nonessential showroom decoration    (d) size of the packaging used for returned motors
  16. Which action does NOT follow good practice when inspecting slip rings and commutators? (a) Treating both components as identical and applying the same undercutting process indiscriminately    (b) Identifying the machine type    (c) Checking brush contact condition    (d) Inspecting wear before machining
  17. The main reason electrical installations follow statutory regulations is to ________. (a) allow terminals to remain uninsulated    (b) remove the need for circuit identification    (c) replace continuity testing with visual colour checks    (d) establish minimum safety and workmanship requirements
  18. Which of these is not a data communication cable type? (a) Twisted-pair cable    (b) Coaxial cable    (c) Winding enamel alone    (d) Fibre-optic cable
  19. A conventional DC armature has a rough commutator surface. The correct step is to ________. (a) inspect wear and use appropriate maintenance procedures before recommissioning    (b) undercut every slip ring regardless of design    (c) increase the supply voltage until sparking stops    (d) operate indefinitely without examining brush contact
  20. The correct step when using a simple primary cell in a test circuit is to ________. (a) connect its terminals directly together for continuous use    (b) attempt unrestricted charging of every primary cell    (c) observe polarity and avoid a short circuit    (d) use damaged insulation for the conductors
  21. ________ describes a cell that is generally intended for use without routine electrical recharging. (a) A primary cell    (b) A secondary accumulator    (c) A rechargeable storage cell    (d) A reversible accumulator
  22. The main reason a starter may be necessary for an electric motor is ________. (a) to make the motor independent of its supply rating    (b) to control starting current and operation as required    (c) to replace earthing and overcurrent protection    (d) to ensure all motor types use the same wiring
  23. A rewinding contractor prices a job using wire and labour only, ignoring overhead. The likely consequence is ________. (a) overstating every material cost by definition    (b) eliminating the need for a budget    (c) underestimating the full cost and setting an unsustainable price    (d) making every proposal automatically profitable
  24. All these can appear in an electrical-installation business proposal except ________. (a) estimated material costs    (b) expected labour requirements    (c) a cash-flow or financing plan    (d) a promise to disregard mandatory installation safety rules
  25. Which of the following best explains why ordinary primary cells should not be treated as rechargeable batteries? (a) All primary cells contain no chemical energy    (b) Their chemistry and construction are not generally designed for safe repeated reversal of reaction    (c) Secondary cells lack electrodes    (d) Primary cells convert electricity only into mechanical work
  26. All these are features relevant to motor installation except ________. (a) correct enclosure    (b) suitable starter    (c) secure mounting    (d) manufacturer’s promotional slogan
  27. A motor is installed in a dusty environment. The ________ should be selected with the operating environment in mind. (a) location of the service centre signboard    (b) protective enclosure    (c) pricing of the repair contract    (d) brand of a storage cabinet
  28. The correct step before terminating data cabling is to ________. (a) mix cable pairs at random    (b) strip insulation beyond the connector without need    (c) identify the cable standard and verify the required pin-out or termination scheme    (d) assume every connector supports every medium
  29. Which of the following first-aid box provisions is appropriate for an electrical workshop? (a) Suitable dressings and other approved first-aid materials    (b) Open containers of petrol kept with dressings    (c) Loose energised test leads among bandages    (d) Unlabelled solvent bottles in place of supplies
  30. Which of these is not an appropriate motor-installation verification step? (a) Checking insulation and connections    (b) Confirming a suitable starter and rating    (c) Energising before checking earth continuity and mechanical mounting    (d) Checking rotation and protection under controlled conditions
  31. The ________ test checks whether a motor coil has an uninterrupted electrical path. (a) surface-colour    (b) fluid-level    (c) advertisement-response    (d) continuity
  32. Which of the following best distinguishes a motor from a generator? (a) A motor converts electrical energy to mechanical output, while a generator does the reverse    (b) Both convert mechanical energy to sound only    (c) A motor always produces electricity for external loads    (d) A generator can operate without any energy input
  33. Which of the following most clearly indicates an unsafe conductor termination? (a) Properly secured conductor under a suitable terminal    (b) Insulated joint inside an appropriate enclosure    (c) Correctly labelled terminal connections    (d) Frayed copper strands protruding into adjacent live terminals
  34. The main reason an electrical accident record should be maintained is to ________. (a) replace immediate first aid    (b) document the event for investigation and prevention of recurrence    (c) prove that equipment cannot fail again    (d) make protective devices unnecessary
  35. A workshop needs communication links between control equipment. Which cable-selection consideration is most important? (a) Only the colour of cable outer packaging    (b) Assuming every cable carries the same type of signal    (c) Using damaged insulation to reduce costs    (d) Signal requirements, environment and allowable cable length
  36. The correct step before dismantling a motor for rewinding is to ________. (a) cut all wires without recording positions    (b) remove every insulation label as unnecessary    (c) record its winding connections, terminal markings and relevant dimensions    (d) choose a wire size only from its outer colour
  37. Which action does NOT support reliable motor rewind insulation? (a) Using proper slot insulation    (b) Allowing coil conductors to scrape unprotected against the core    (c) Protecting winding end turns    (d) Checking insulation before energising
  38. An apprentice finds a colleague in contact with a live conductor. Which of the following actions has priority? (a) Pull the person away immediately using bare hands    (b) Pour water on the conductor to cool it    (c) Isolate the supply safely before approaching or touching the casualty    (d) Move the casualty while still in contact with live equipment
  39. The main reason to solder a terminal only where the termination design permits it is that ________. (a) a joint must remain electrically sound and mechanically suitable in service    (b) solder compensates for all loose conductor strands automatically    (c) a shiny solder surface proves the wire is adequately rated    (d) terminals no longer require inspection after soldering
  40. ________ is used in a conventional AC machine as a rotating electrical contact where the design requires continuous contact without commutation. (a) A segmented commutator in every design    (b) A slip ring    (c) A ferrite transformer core    (d) An insulating mounting foot

SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.

1. Answer the following questions.
(a) A motor-repair workshop has a live-conductor accident. Outline FIVE immediate safety and first-aid actions in a defensible sequence. (5 marks)
(b) Evaluate FIVE conductor-handling or statutory-compliance decisions before an installation is energised. (5 marks)

2. Answer the following questions.
(a) A faulty motor requires rewinding. Explain FIVE records or tests needed to reproduce its winding safely. (5 marks)
(b) Distinguish FIVE considerations associated with commutators, slip rings and armature maintenance. (5 marks)

3. Answer the following questions.
(a) Compare primary and secondary cells and AC and DC machines using FIVE technically accurate points. (5 marks)
(b) Explain FIVE installation checks before recommissioning a repaired electric motor. (5 marks)

4. Answer the following questions.
(a) A technician sets up communication and power equipment in a repair workshop. Identify FIVE relevant cable, tool and testing choices. (5 marks)
(b) Prepare FIVE major budget or business-plan considerations for starting a motor-rewinding service. (5 marks)


OBJECTIVE MARKING SCHEME
Question 1 – ✅ (a) Recording the circumstances and reporting the incident
Question 2 – ✅ (c) continuity does not replace insulation resistance and earthing checks
Question 3 – ✅ (a) conductor cross-section affects resistance, heating and current capacity
Question 4 – ✅ (d) inspect load, starter, protective settings and supply conditions before restarting
Question 5 – ✅ (b) Touching the casualty before the supply is made safe
Question 6 – ✅ (a) Commutator surface, brushes and the repaired coil connections
Question 7 – ✅ (c) commutator
Question 8 – ✅ (d) Number of turns, conductor size and connection arrangement
Question 9 – ✅ (b) winding diagram
Question 10 – ✅ (c) Reliable transfer of the intended signals under the specified conditions
Question 11 – ✅ (d) secondary cell
Question 12 – ✅ (b) the customer’s preferred brand name on an unrelated advert
Question 13 – ✅ (a) current-carrying capacity and insulation suitability
Question 14 – ✅ (d) Leaving exposed loose strands that may bridge adjacent terminals
Question 15 – ✅ (b) repayment obligations and operating cash flow
Question 16 – ✅ (a) Treating both components as identical and applying the same undercutting process indiscriminately
Question 17 – ✅ (d) establish minimum safety and workmanship requirements
Question 18 – ✅ (c) Winding enamel alone
Question 19 – ✅ (a) inspect wear and use appropriate maintenance procedures before recommissioning
Question 20 – ✅ (c) observe polarity and avoid a short circuit
Question 21 – ✅ (a) A primary cell
Question 22 – ✅ (b) to control starting current and operation as required
Question 23 – ✅ (c) underestimating the full cost and setting an unsustainable price
Question 24 – ✅ (d) a promise to disregard mandatory installation safety rules
Question 25 – ✅ (b) Their chemistry and construction are not generally designed for safe repeated reversal of reaction
Question 26 – ✅ (d) manufacturer’s promotional slogan
Question 27 – ✅ (b) protective enclosure
Question 28 – ✅ (c) identify the cable standard and verify the required pin-out or termination scheme
Question 29 – ✅ (a) Suitable dressings and other approved first-aid materials
Question 30 – ✅ (c) Energising before checking earth continuity and mechanical mounting
Question 31 – ✅ (d) continuity
Question 32 – ✅ (a) A motor converts electrical energy to mechanical output, while a generator does the reverse
Question 33 – ✅ (d) Frayed copper strands protruding into adjacent live terminals
Question 34 – ✅ (b) document the event for investigation and prevention of recurrence
Question 35 – ✅ (d) Signal requirements, environment and allowable cable length
Question 36 – ✅ (c) record its winding connections, terminal markings and relevant dimensions
Question 37 – ✅ (b) Allowing coil conductors to scrape unprotected against the core
Question 38 – ✅ (c) Isolate the supply safely before approaching or touching the casualty
Question 39 – ✅ (a) a joint must remain electrically sound and mechanically suitable in service
Question 40 – ✅ (b) A slip ring


THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: Isolate energy without unsafe contact (1); secure the area (1); call suitable emergency assistance (1); assess or assist casualty only when safe within competence (1); document and report after immediate response (1).
(b) 5 marks: Appropriate conductor rating (1); intact insulation (1); suitable terminal methods (1); correct earthing and protection (1); inspection and test before energising (1).
Question 2 (10 Marks)
(a) 5 marks: Document winding layout (1); measure conductor size (1); count turns or coils (1); restore suitable slot or end-turn insulation (1); perform continuity and insulation checks (1).
(b) 5 marks: Recognise DC commutation purpose (1); identify slip-ring continuous contact (1); inspect wear (1); check brush contact (1); select appropriate surface machining and avoid incorrect undercutting (1).
Question 3 (10 Marks)
(a) 5 marks: Primary single-use design (1); secondary rechargeable design (1); motor energy conversion (1); generator conversion in reverse direction (1); conventional DC commutation versus suitable AC design (1).
(b) 5 marks: Suitable enclosure (1); correct starter and voltage rating (1); secure mounting (1); earthing and insulation testing (1); controlled rotation and protective checks (1).
Question 4 (10 Marks)
(a) 5 marks: Select appropriate data cable medium (1); correct termination (1); safe electrical tools (1); suitable winding tool for repair (1); continuity or earth test equipment (1).
(b) 5 marks: Estimate materials and parts (1); price labour and overhead (1); select or finance equipment (1); plan cash flow or borrowing (1); ensure safe compliant service (1).

Export this post
First Term Electrical Installation and Maintenance Work Examination for SS 3
About the author

Royal Alikor

Royal Alikor is an educator with six years of classroom teaching and three years of elementary school leadership experience. He develops and reviews practical, curriculum-aligned learning materials for Nigerian schools.

Community Join the conversation Open discussion +