Skip to content
HeadTeacher.ng
Examinations

First Term Dying and Bleaching Examination for SS 3

First Term Dying and Bleaching Examination for SS 3. This SS 3 lesson follows the scheme of work.

Published Reading14 min Comments0

Class: SSS 3
Term: First Term
Subject: Dying and Bleaching
Time: 2 Hours 30 Minutes
Total Marks: 70


SECTION A: OBJECTIVES (40 Marks)
Instruction: Answer ALL 40 questions. Each question carries 1 mark.

  1. An example of a batik design created by scattering molten resist across cloth is ________. (a) engraving an intaglio plate    (b) wax-splash patterning    (c) cutting a screen stencil only    (d) applying a plain uniform bleach wash
  2. Which of the following explains why a wax-resist pattern remains undyed in selected areas? (a) Wax permanently changes cotton into synthetic fibre    (b) Wax converts the dye into a screen-printing mesh    (c) Wax increases dye penetration wherever it is applied    (d) Wax acts as a barrier against the dye reaching those fibres
  3. The ________ technique differs from relief printing because ink is held in recessed areas. (a) screen-resist    (b) intaglio    (c) starching    (d) broom splashing
  4. All of these are legitimate screen-printed fabric products except ________. (a) a cushion cover    (b) a table cover    (c) a fabric bag    (d) an unprinted plain fabric with no transferred image
  5. ________ offers a way to reproduce a repeated starch-resist motif with defined edges. (a) Random application without a repeat guide    (b) Wax splashing without stencil registration    (c) Stencilling    (d) An uncontrolled all-over dye dip
  6. A printed motif breaks during drying because the paste does not adhere well. The correct step is to ________. (a) review paste preparation and the fabric surface before repeating the print    (b) increase random splashing without checking the paste    (c) replace the fabric with a metal plate    (d) block the entire pattern with permanent paint
  7. Which of the following best distinguishes wax-resist batik from starch resist? (a) Only starch methods can be patterned    (b) Both methods require printing from engraved metal plates    (c) The resisting substance differs even though both protect selected areas from dye    (d) Wax batik always uses no dyes
  8. The correct step when a printer notices a blurred repeat image is to ________. (a) check fabric positioning, screen registration and paste control    (b) increase printing pressure at random without checking alignment    (c) use the wrong side of every frame deliberately    (d) ignore the first defective prints and continue
  9. All these can influence the quality of a starch-resist print except ________. (a) paste consistency    (b) the colour of the unused screen-frame handle    (c) stencil placement    (d) fabric surface preparation
  10. The main reason a starch paste can produce a resist design is that it ________. (a) acts as a permanent coloured yarn    (b) makes the fabric unsuitable for washing    (c) replaces the need to prepare a design    (d) temporarily prevents or reduces dye contact with covered fabric areas
  11. Which action does NOT favour controlled wax-resist production? (a) Preparing fabric before treatment    (b) Handling hot wax with suitable protection    (c) Applying dangerously overheated wax without checking equipment    (d) Planning protected and exposed design areas
  12. A technician wishes to obtain a patterned rather than an all-over batik finish. The most important design decision is ________. (a) where the wax should resist dye uptake    (b) the decorative presentation of the final package    (c) whether to dye the entire cloth before placing any resist    (d) whether to align a later screen print with the finished pattern
  13. The main reason to maintain even mesh tension on a printing frame is to ________. (a) make all patterns transfer without colour    (b) eliminate every need for screen preparation    (c) support accurate and repeatable transfer of the design    (d) convert silk screen printing into intaglio
  14. Which action does NOT help preserve a reusable screen after printing? (a) Leaving dye paste to dry and block the mesh openings    (b) Removing residual paste promptly    (c) Rinsing with appropriate cleaning procedures    (d) Storing the screen without damaging its mesh
  15. A design is intended to show fine lines rather than large splashes. Which of the following tools is most suitable for controlled molten-wax application? (a) Large drying basket    (b) Flat iron used only for final pressing    (c) Tjanting-style wax applicator    (d) Cutting slab for fish preparation
  16. The ________ in screen printing carries the open and blocked areas through which colour is transferred. (a) wooden mallet    (b) mesh screen    (c) wax-melting bowl    (d) drying basket
  17. The ________ should be considered when deciding whether a wax-splash resist will produce fine or broad marks. (a) wording of the fabric sales label    (b) weight of the finished package rather than the wax droplets    (c) length of fabric planned for later packaging    (d) size and control of wax droplets
  18. An irregular splash effect is required on two metres of fabric. Which procedure best matches the stated practical? (a) Protect the work area, splash controlled amounts of wax, then dye exposed fabric    (b) Start with engraving a metal plate    (c) Rub dry powder onto every motif as a permanent mask    (d) Cover the whole fabric uniformly in wax before colouring
  19. All these can be used to apply starch-resist patterns except ________. (a) a stencil    (b) an unprepared engraving plate used without resist paste    (c) a stamp    (d) free-hand application
  20. Which of these is not a basis for distinguishing relief, intaglio and planographic printing? (a) The printing worker’s preferred lunch    (b) Whether image areas are raised    (c) Whether image areas are recessed    (d) Whether image and non-image areas lie in one plane
  21. Which of the following best describes stamping in starch-resist production? (a) Dragging ink from recessed metal lines    (b) Repeated pressing of a prepared motif carrying paste onto fabric    (c) Moving fabric beneath an unprepared screen    (d) Melting wax with an electric soldering iron
  22. The correct step before transferring a prepared design through a screen is to ________. (a) pull a loose mesh over wet fabric without tension    (b) discard the screen frame before use    (c) ensure the mesh is properly fixed and the intended image areas are prepared    (d) block every mesh opening regardless of the design
  23. Which of the following correctly describes planographic printing? (a) Image and non-image areas are essentially on the same plane    (b) Ink is held only in engraved grooves    (c) Only raised blocks can carry the image    (d) A wax barrier must first cover every printed area
  24. The main reason the printing mesh must contain both open and blocked areas is to ________. (a) remove all need to select a fabric    (b) define which parts of the design receive colour    (c) replace the printing paste with hot water    (d) make all printed areas identical in colour automatically
  25. The correct step after a screen-printing run is to ________. (a) allow thick ink to harden permanently in the mesh    (b) stack wet prints so patterns transfer to adjacent fabrics    (c) clean the mesh and equipment before residue blocks intended openings    (d) remove the stencil without regard to its condition
  26. Which of the following is most suitable for placing repeated identical starch motifs at intervals? (a) Applying paste at random without a guide    (b) Stamping with a prepared motif    (c) Removing paste before any pattern is marked    (d) Using only an unmarked melting bowl
  27. ________ is the stage at which a prepared design is transferred into suitable image and non-image areas of the mesh. (a) Fish scaling    (b) Hair conditioning    (c) Motor rewinding    (d) Screen preparation
  28. A student wants a free-hand resist design that is not limited by a stencil outline. The strongest choice is ________. (a) using a fixed repeat stamp for every line    (b) direct application of starch paste with a drawing tool    (c) substituting mesh transfer without applying starch    (d) cutting a garment pattern as the design itself
  29. When a fabric bag requires the same logo repeatedly, screen printing is attractive mainly because ________. (a) the prepared screen can reproduce a consistent motif    (b) screen printing always avoids any setup cost    (c) each print must have a different unintended pattern    (d) there is no need to align the fabric
  30. Which of these is not a printing process listed in the scheme? (a) Relief    (b) Tie-and-fold resist dyeing    (c) Intaglio    (d) Planographic
  31. A fabric intended for a table cover needs a repeated decorative border. The strongest combined method is ________. (a) dye everything first and expect unmarked areas to appear    (b) apply all paste with no positioning guide    (c) use only a heated clipper blade to cut the motif    (d) prepare a border motif, apply consistent starch resist, dye, and remove the temporary resist
  32. The main reason an iron or hot-water treatment may be included in wax-resist work is ________. (a) to convert relief printing into weaving    (b) to permanently glue wax into the fabric    (c) to help remove the resist after the dyeing stage    (d) to substitute for all design planning
  33. The ________ should be tested when a starch-resist pattern washes out before dyeing is complete. (a) amount of paste lost through an incorrectly placed stencil    (b) shape of the workshop’s roof    (c) advertised colour of the printing-frame handle    (d) adhesion and drying of the resist paste
  34. Which of these is not normally a screen-printing process step? (a) Cutting the finished fabric before its image has been transferred    (b) Preparing the mesh and frame    (c) Transferring the design    (d) Printing and fixing the fabric image
  35. All these materials may be appropriate to wax-resist batik except ________. (a) fabric    (b) resist wax    (c) an empty mesh screen used without applying wax    (d) dye bath
  36. Which action does NOT help make starch-resist marks sharp and consistent? (a) Securing the stencil position    (b) Applying paste at controlled thickness    (c) Allowing suitable drying before the next stage    (d) Moving the stencil before completing the application
  37. ________ is a printing method in which ink is transferred from raised areas of a printing surface. (a) Relief printing    (b) Intaglio printing    (c) Planographic printing    (d) Starch-resist dyeing
  38. Which technique creates an image by allowing colour through selected openings of a mesh? (a) Engraved-line intaglio    (b) Flat-surface planographic printing    (c) Hand-knitting    (d) Screen printing
  39. The correct step when wax unintentionally spreads beyond the planned motif is to ________. (a) assume the error will disappear under every dye    (b) add more random wax without inspection    (c) assess the affected design area before proceeding with dyeing    (d) immerse unprotected fabric immediately without reconsideration
  40. The ________ should be controlled to prevent uneven resistance from unintended spills during batik production. (a) colour of a storage label    (b) size of the student’s exercise book    (c) number of windows in the classroom    (d) application of molten wax

SECTION B: THEORY (30 Marks)
Instruction: Answer Question 1 and any other TWO questions. Each question carries 10 marks.

1. Answer the following questions.
(a) Design a wax-resist batik piece by identifying FIVE decisions or stages from planning to patterned dyeing. (5 marks)
(b) Explain FIVE factors that could make a wax-splash motif inconsistent or unsafe in production. (5 marks)

2. Answer the following questions.
(a) A student must produce repeated starch-resist motifs. Outline FIVE stages for making the design with a stencil or stamp. (5 marks)
(b) Compare FIVE considerations when choosing free-hand, stencilling and stamping for starch-resist work. (5 marks)

3. Answer the following questions.
(a) Distinguish relief, intaglio, planographic and screen printing by giving FIVE relevant explanations or comparisons. (5 marks)
(b) Describe FIVE steps for preparing and using a mesh frame to print a repeat image on fabric. (5 marks)

4. Answer the following questions.
(a) A craft business plans to screen-print fabric bags and cushion covers. Identify FIVE production-control measures needed for consistent results. (5 marks)
(b) Explain FIVE reasons for cleaning and safely handling printing and dyeing tools after production. (5 marks)


OBJECTIVE MARKING SCHEME
Question 1 – ✅ (b) wax-splash patterning
Question 2 – ✅ (d) Wax acts as a barrier against the dye reaching those fibres
Question 3 – ✅ (b) intaglio
Question 4 – ✅ (d) an unprinted plain fabric with no transferred image
Question 5 – ✅ (c) Stencilling
Question 6 – ✅ (a) review paste preparation and the fabric surface before repeating the print
Question 7 – ✅ (c) The resisting substance differs even though both protect selected areas from dye
Question 8 – ✅ (a) check fabric positioning, screen registration and paste control
Question 9 – ✅ (b) the colour of the unused screen-frame handle
Question 10 – ✅ (d) temporarily prevents or reduces dye contact with covered fabric areas
Question 11 – ✅ (c) Applying dangerously overheated wax without checking equipment
Question 12 – ✅ (a) where the wax should resist dye uptake
Question 13 – ✅ (c) support accurate and repeatable transfer of the design
Question 14 – ✅ (a) Leaving dye paste to dry and block the mesh openings
Question 15 – ✅ (c) Tjanting-style wax applicator
Question 16 – ✅ (b) mesh screen
Question 17 – ✅ (d) size and control of wax droplets
Question 18 – ✅ (a) Protect the work area, splash controlled amounts of wax, then dye exposed fabric
Question 19 – ✅ (b) an unprepared engraving plate used without resist paste
Question 20 – ✅ (a) The printing worker’s preferred lunch
Question 21 – ✅ (b) Repeated pressing of a prepared motif carrying paste onto fabric
Question 22 – ✅ (c) ensure the mesh is properly fixed and the intended image areas are prepared
Question 23 – ✅ (a) Image and non-image areas are essentially on the same plane
Question 24 – ✅ (b) define which parts of the design receive colour
Question 25 – ✅ (c) clean the mesh and equipment before residue blocks intended openings
Question 26 – ✅ (b) Stamping with a prepared motif
Question 27 – ✅ (d) Screen preparation
Question 28 – ✅ (b) direct application of starch paste with a drawing tool
Question 29 – ✅ (a) the prepared screen can reproduce a consistent motif
Question 30 – ✅ (b) Tie-and-fold resist dyeing
Question 31 – ✅ (d) prepare a border motif, apply consistent starch resist, dye, and remove the temporary resist
Question 32 – ✅ (c) to help remove the resist after the dyeing stage
Question 33 – ✅ (d) adhesion and drying of the resist paste
Question 34 – ✅ (a) Cutting the finished fabric before its image has been transferred
Question 35 – ✅ (c) an empty mesh screen used without applying wax
Question 36 – ✅ (d) Moving the stencil before completing the application
Question 37 – ✅ (a) Relief printing
Question 38 – ✅ (d) Screen printing
Question 39 – ✅ (c) assess the affected design area before proceeding with dyeing
Question 40 – ✅ (d) application of molten wax


THEORY MARKING SCHEME (Answer 3 × 10 = 30 Marks)
Question 1 (10 Marks)
(a) 5 marks: Plan motif and protected areas (1); prepare fabric and tools (1); melt or apply wax with safety measures (1); dye exposed areas (1); remove resist and finish fabric suitably (1).
(b) 5 marks: Uncontrolled wax temperature (1); inconsistent droplet size (1); unsuitable fabric preparation (1); poor tool handling (1); unintended spreading or inadequate drying (1).
Question 2 (10 Marks)
(a) 5 marks: Design repeat (1); prepare starch paste (1); position stencil or stamp (1); apply paste accurately (1); dry, dye and remove resist suitably (1).
(b) 5 marks: Unique free-hand marks (1); stencil sharpness (1); stamp repeatability (1); paste consistency (1); registration or placement control (1).
Question 3 (10 Marks)
(a) 5 marks: Raised relief surface (1); recessed intaglio image (1); same-plane planographic principle (1); mesh openings in screen printing (1); suitable use of method for the design (1).
(b) 5 marks: Mount or secure mesh (1); prepare image and non-image areas (1); position fabric (1); transfer paste through screen (1); dry or fix and clean equipment (1).
Question 4 (10 Marks)
(a) 5 marks: Suitable fabric and ink (1); clear stencil or design (1); correct mesh tension (1); registration between prints (1); drying and fixing (1).
(b) 5 marks: Avoid mesh blockage (1); preserve stencil or frame (1); remove leftover dye (1); reduce unintended cross-colour contamination (1); prevent injury from tools or hot substances (1).

Export this post
First Term Dying and Bleaching Examination for SS 3
About the author

Royal Alikor

Royal Alikor is an educator with six years of classroom teaching and three years of elementary school leadership experience. He develops and reviews practical, curriculum-aligned learning materials for Nigerian schools.

Community Join the conversation Open discussion +